Re: Track speed is very hy #define


hmsampaio@...
 

Hi, thanks to respond. My mount is a project about thingverse, small travel 3d mount, it have two step motors whith planetarium reduction 100/1, but when i finist all, the track speed is very high.
this my way to change in arduino IDE

// AXIS1 RA/AZM
// see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS1
#define AXIS1_STEPS_PER_DEGREE    1777.77778 //  12800, n. Number of steps per degree:                                          <-Req'd
                                          //         n = (stepper_steps * micro_steps * overall_gear_reduction)/360.0
#define AXIS1_STEPS_PER_WORMROT     64000 //  12800, n. Number of steps per worm rotation (PEC Eq mode only:)                <-Req'd
                                          //         n = (AXIS1_STEPS_PER_DEGREE*360)/reduction_final_stage
 
#define AXIS1_DRIVER_MODEL            DRV8825 //    OFF, (See above.) Stepper driver model.                                      <-Often
#define AXIS1_DRIVER_MICROSTEPS       32 //    OFF, n. Microstep mode when tracking.                                        <-Often
#define AXIS1_DRIVER_MICROSTEPS_GOTO  16 //    OFF, n. Microstep mode used during gotos.                                     Option
#define AXIS1_DRIVER_IHOLD            OFF //    OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0                    Option
#define AXIS1_DRIVER_IRUN             OFF //    OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc.    Option
#define AXIS1_DRIVER_IGOTO            OFF //    OFF, n, (mA.) Current during slews. OFF uses same as IRUN.                    Option
#define AXIS1_DRIVER_REVERSE          OFF //    OFF, ON Reverses movement direction, or reverse wiring instead to correct.   <-Often
#define AXIS1_DRIVER_STATUS           OFF //    OFF, TMC_SPI, HIGH, or LOW.  Polling for driver status info/fault detection.  Option
 
#define AXIS1_LIMIT_UNDER_POLE        180 //    180, n. Where n=150..180 (degrees.) Max HA hour angle + or - for Eq modes.    Infreq
#define AXIS1_LIMIT_MAXAZM            360 //    360, n. Where n=180..360 (degrees.) Max Azimuth + or - for AltAzm mode only.  Infreq
 
// AXIS2 DEC/ALT
// see https://onstep.groups.io/g/main/wiki/6-Configuration#AXIS2
#define AXIS2_STEPS_PER_DEGREE    1760.88889 //  12800, n. Number of steps per degree:                                          <-Req'd
                                          //         n = (stepper_steps * micro_steps * overall_gear_reduction)/360.0
 
#define AXIS2_DRIVER_MODEL            DRV8825 //    OFF, (See above.) Stepper driver model.                                      <-Often
#define AXIS2_DRIVER_MICROSTEPS       32 //    OFF, n. Microstep mode when tracking.                                        <-Often
#define AXIS2_DRIVER_MICROSTEPS_GOTO  16 //    OFF, n. Microstep mode used during gotos.                                     Option
#define AXIS2_DRIVER_IHOLD            OFF //    OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0                    Option
#define AXIS2_DRIVER_IRUN             OFF //    OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc.    Option
#define AXIS2_DRIVER_IGOTO            OFF //    OFF, n, (mA.) Current during slews. OFF uses same as IRUN.                    Option
#define AXIS2_DRIVER_POWER_DOWN       OFF //    OFF, ON Powers off 10sec after movement stops or 10min after last<=1x guide.  Option
#define AXIS2_DRIVER_REVERSE          OFF //    OFF, ON Reverses movement direction, or reverse wiring instead to correct.   <-Often
#define AXIS2_DRIVER_STATUS           OFF //    OFF, TMC_SPI, HIGH, or LOW.  Polling for driver status info/fault detection.  Option
#define AXIS2_TANGENT_ARM             OFF //    OFF, ON +limit range below. Set cntr w/[Reset Home] Return cntr w/[Find Home] Infreq

Join main@onstep.groups.io to automatically receive all group messages.