Date   

Re: My 16" dob with Onstep

Butchf
 


Re: SHC Enclosure - Printed, no PCB needed :)

Butchf
 

Did you post the Wiring diagram somewhere?

thanks,
Don


Re: EQ5 Build - V1.0 Released #EQ5

Jesse Lichtenberg
 

Very nice build - thank you for sharing the information! I am looking to upgrade a manual EQ5 to OnStep and I knew there were some great examples in the showcase, but I hadn't been back recently enough to see this one. I may be following your design more or less exactly! 

You'd mentioned having other pulleys and belts on the way - anything you'd care to elaborate on? I'm going to start putting together my parts list!


Re: My 16" dob with Onstep

Oscar Lithgow
 

Butchf... Where did you get those "Latches handles" you are using for engaging the mechanism? 


Re: Simple question about Onstep Version code

Plamen Dimitrov
 

Thanks a lot! This is exactly I wanted.
this will be helpful to track how mine maxesp3 responds to future possible updates of the firmware code.
thanks.
+Plamen


Re: Simple question about Onstep Version code

Khalid Baheyeldin
 

Open the OnStep.ino file, scroll down a page or so, and look at these values:

#define FirmwareVersionMajor  5
#define FirmwareVersionMinor  0
#define FirmwareVersionPatch  "f"


Re: Simple question about Onstep Version code

Plamen Dimitrov
 

Thanks Khalid,
probably I did not express myself clearly.
Let say that I just downloaded a version of onstep code right now and have not uploaded to the controller yet and the code is still in my computer.

How do I know the version of onstep to be uploaded into the controller before been uploaded into the controller?
+ Plamen


Re: Simple question about Onstep Version code

Khalid Baheyeldin
 

On Mon, Dec 28, 2020 at 03:29 PM, Plamen Dimitrov wrote:
Does anybody knows a simple way to know what version Onstep code (freshly downloaded) was prior uploading on the Onstep Hardware controllers ?
If you mean: "what version is my controller running now", then yes.
If you have WiFi and use the web interface, it will be displayed on the Status page.
The Android app also shows it (press the "i" several times).

If you don't have WiFi, you can still know over USB. Use the IDE's Serial Monitor and enter
the command:

:GVN#


Simple question about Onstep Version code

Plamen Dimitrov
 

Hello every everyone,
Does anybody knows a simple way to know what version Onstep code (freshly downloaded) was prior uploading on the Onstep Hardware controllers ?
Thanks
+Plamen


Re: Combining OnStep with Celestron #celestron

Egge
 

Hi Chris,

great documentation! Thank you very much. Based on this, I decided to disasemble the mount and do at lease some improvements (e.g. cleaning; new grease; replace ball bearings,...). After this (and of course testing) I will decide, wether I transform the mount to OnStep... but this will be far in the future...

May I ask a few questions, to be prepared for disasembling:
1. you mentioned, to replace the worm shaft bearings... can you please give an example of the bearings you used?
2. you also mentioned, that you have replaced the big bearings (6008-2RS). Can you recommend this? Did you see some improvements?
3. do you also recommend to do something with the teflon washers and/or adding shims (as decreibed in Astro-Baby)?

And a few questions for a possible OnStep-transformation
1. since you finally recommended the 48/15 ratio of pulleys, it requires no mechanical adaptions on the mount - only on the width of the 48teeth pulley?
2. center to center distance from worm gear to motor axis is 50-53mm?
3. only reason for you to use MXL was availability? would there be any disadvantages on GT2?
4. how tricky was the asemmbly of motor inside the mount and connect it to the timing belt?
5. I always have problems with my 12V DC power supply connectors - what connector (male and female) did you use exactly?

thanks in advance...
egge


Uploading to MaxESP3

@Northwind
 

I've built a MaxESP3, based on the ESP-WROOM-32 (Node-MCU), 38-pin board. I got it working with the SHC controller (same board), but the motors would only move if I selected a speed of 8X or slower. I'd like to upload the firmware with a few tweaks, but I can't get it to upload. I'm getting the error message: "A fatal error occurred: Failed to connect to ESP32: Invalid head of packet (0x00)". I tried every possible manipulation of the EN button on the board while trying to upload, but always get the same message.

Has anyone run across this before? Any suggestions? I'm getting so close.


Re: Where is the code for the latest Master Version of Onstep?

Khalid Baheyeldin
 

On Mon, Dec 28, 2020 at 12:07 PM, Gerry Byrne wrote:
The Wiki for the FYSTC S6 contains the following advice.
 
"To use the FYSETC S6 board, you need to use the latest master version of OnStep (
4.7d or later)"

Is this the code available from the following location?

https://github.com/hjd1964/OnStep.git

Gerry Byrne
This is the 4.x branch. 
Perhaps Howard should change the branch name from just "beta" to "beta (4.x)"

https://github.com/hjd1964/OnStep/archive/beta.zip


Where is the code for the latest Master Version of Onstep?

Gerry Byrne
 

Hi,
The Wiki for the FYSTC S6 contains the following advice.
 
"To use the FYSETC S6 board, you need to use the latest master version of OnStep (
4.7d or later)"

Is this the code available from the following location?

https://github.com/hjd1964/OnStep.git

Gerry Byrne





--
Copernicus


Re: OnStep up and running!!!

Khalid Baheyeldin
 

On Mon, Dec 28, 2020 at 05:46 AM, Egge wrote:
I will try both... reducing mechanical backlash by adjusting mount AND balancing the wheight.
In addition to the above, or even before that, try to adjust the backlash in OnStep.
During daylight, and with the highest magnification, and tracking off, manually slew to a far away land object.
Use the Android app or SHC, and press the W button, then reverse it by pressing E.
If the object lags, then backlash compensation is too low, increase it.
If the object jumps, then backlash compensation is too high, decrease it.
Keep trying until you get no jump or lag.
Do the same for DEC using N and S.

Now, PHD2 has less of the backlash to worry about ...

and just for curiosity... what do you think is a reasonable value for guiding deviation (e.g. 1arc-sec) to get good astro-images? Do you think this can be achieved with EQ5?
I had good 5 minute images with a total RMS of 1.2".
Rarely, I get 0.7" total RMS.
No idea what the reasons can be. There are many: seeing, wind, balance, gears, and so on, and it is hard for me to track down what exactly it is. Since the images are acceptable, I don't care much ...


Re: Motors not Spinning at Low Rates #error

Howard Dutton
 
Edited

On Sun, Dec 27, 2020 at 11:24 PM, Pupper wrote:
So according to this isn't Vref = Imax?
Exactly.  And all other (non TMC) step stick drivers I know of don't factor in the RMS current (*0.71) with their Vref formulas, so I adopted the convention here that TMC drivers use Vref = Imax for consistency.


Re: OnStep up and running!!!

Matt
 

It's possible. I'm getting around 1" with an eq3-2 using multiple stars in Phd2.


On Mon, Dec 28, 2020, 11:46 AM Egge <eckard.deichsel@...> wrote:
Thanks a lot!

I will try both... reducing mechanical backlash by adjusting mount AND balancing the wheight.

and just for curiosity... what do you think is a reasonable value for guiding deviation (e.g. 1arc-sec) to get good astro-images? Do you think this can be achieved with EQ5?


Re: OnStep up and running!!!

Egge
 

Thanks a lot!

I will try both... reducing mechanical backlash by adjusting mount AND balancing the wheight.

and just for curiosity... what do you think is a reasonable value for guiding deviation (e.g. 1arc-sec) to get good astro-images? Do you think this can be achieved with EQ5?


Re: SHC Enclosure - Printed, no PCB needed :)

MartinL
 

I added CAD files as step filesin the Thingiverse repository. Feel free derive your version. Just share your results with community:)


Re: Motors not Spinning at Low Rates #error

Pupper
 

For the TMC2100 here is the formula:

So according to this isn't Vref = Imax?


Re: OnStep up and running!!!

Jay Murphy
 

Yes I agree, it's taking PHD2 a long time to wind out the backlash in your DEC, keep it balanced slightly south heavy to keep your backlash closed.

16861 - 16880 of 45632