Q: OnStep doesn't point where it should A: There is a problem with your drive design and/or configuration and/or software setup, etc. Drive design: Motors and drive components move the mount reliably,

#EQ3

cheers Chad will give it a try and re-check jumpers

#wemos #cnc3 #eq2 #EQ3

The EQ-3-2 has a 130:1 RA reduction and a 65:1 Dec. Compare the estimated tracking resolution. Gear Reduction Tracking STEPS/arc-deg Stepper-Steps MICROSTEPS GR1 GR2 res olution RA 18488.88889 400 32

#arduino #EQ3

Just joined this after my skywatcher motors decided to pack in. Built one using a wemos and cncv3 board seem to work fine but will know better when i get the mounts that you have supplied(Thank you fo

#EQ3

I already had setup Kstars with INDI. I made some goto test With the indoor testing I'm doubt about the movements. -- Kind regards from Belgium, Wolf

#EQ3

Also keep in mind speed kills steppers. The faster you go the less torque you have. You could try changing the slew_acceleration_dist to 10 so you get a slow ramp up to your final speed to get the mas

#wemos #S6 #EQ3 #fysetc #wifi

The D1 R32/Hujer Shield has been used on a few CG-4/EQ-3 and 3-1s. A CG-4 user sent me one of his first photos: I've have some old Palomar images for Jupiter that don't measure up to this.

#EQ3

guys i have a question this is for the eq1 dec above made a direct link and how did he find the value. Also, according to what the microstep step is 64 or 256 and how does the equivalent of 64-4 or 25

#EQ3 #S6

Yes , design comes from Frank in that topic : https://onstep.groups.io/g/main/topic/my_skywatcher_150p_on_an/83327227?p=,,,20,0,0,0::recentpostdate%2Fsticky,,,20,2,120,83327227 I just made some minor

#EQ3 #bluepill

Thank you Howard

#EQ3

Hola, me interesaría contactar contigo para algunas preguntas

#EQ3 #fysetc #wifi #wemos #S6

If your problem is that you cannot flash OnStep on the STM32, then check the Troubleshooting section of the STM32 Wiki. First point about R3 resistor.

#EQ3

George Cushing sells kits and assembled kits at this link OnStep Controller Kits (stmbluepillkits.com) But you still have to do the mount's mechanical conversion yourself.

#EQ3 #EQ5

Open Source means you do it yourself. You are asking for someone to everything for you and no one here has the time or skills. Every telescope is different and every person wants different things. The

#EQ3 #EQ5 #dob

It's probably happened to all of us at one time or another--can make for a wild ride!

#EQ3

I connect to OnStep with the usb of the mega2560, I also have a wemos D1 in the configuration but i've never used

#EQ3

Hello! Would you mind sharing the stepper motor mount so I can print a similar. I ran into the issue where the pulley crashes with the quickrelease on top so I need an extender of sorts, might get the

#EQ3

If the hand controller is compatible with ST4 protocol it should work, right? I tested my Losmandy hand controller with OnStep and it worked fine to move the telescope (although i had to change speed

#wemos #EQ3

Right now I'm using the CNC board with basic Arduino and a4988 drivers that I had here. I'm running it using GRBL just to test wiring, belts and mounts until I get the correct processor. I've ordered

#EQ3 #wemos

You were right, i tried with other DC and i had no problems, once more thank you khalid!

#wemos #fysetc #S6 #EQ3