Perhaps the “pinout” on the motor cable is incorrect. The motor will “jitter” if the phases are incorrect. Not wired correctly. Check the wiring from the driver goes to an appropriate coil on the step

Sent: Friday, 18 March 2022 7:20 AM To: main@onstep.groups.io Subject: Re: [onstep] WeMos D1 Mini Pro All - Thanks everyone for helping. A lot to go through but here are my results Glenn - As requeste

Drew, Only trying to help Mark, not start WW3. The VID / PID shown indicates VID 2341 . A device from Arduino SA. PID 0043 is a Uno R3 (CDC ACM). Just tells me the USB to UART device has worked and th

Drew, The response is from the SIL CP210x device on the USB port. Windows has no further driver to progress. https://community.silabs.com/s/article/downloading-cp210x-drivers-from-windows-update?langu

Mark, Have had this with clone devices before. The VID and PID belong to the onboard CP210x; presumably CP2102 in your case; USB to UART Converter. They are the Vendor ID (VID) and Product ID (PID) fo

Did you need additional libraries or simply set WEATHER in config.h to BME280x076? If so what was needed. Regards, Glenn.

Did you need additional libraries or simply set WEATHER in config.h to BME280x076? Regards, Glenn.

Which library do I need to use BME280 tacked on to the DS3231 on my blue pill. Compile fails if I turn WEATHER to anything other than OFF. The BME 280 is set across the pins of the 3231 and I am prett

George, Is not that “I never make mistrakes”? Be good, Glenn.

Same here, Be patient. After the splash screen… Display shows Starting WIFI: ONSTEP…Restart WIFI: Failed This loop repeats for me at around 10 second intervals. Then ….after 1-3 minutes or so you get…

Upload method is incorrect. Needs STM32 cube programmer (serial). Regards, Glenn.

Thanks Khalid, You confirmed the issue. It took 18 seconds the first time. Then I powered off the wSHC, and tried again. The wSHC kept trying to connect, and took 1 minute 48 seconds to connect I have

So why so long to “connect”? OnStep is stand alone and NOT part of my local network. wSHC is in station mode. It connects and functions properly. The time to make the connection is my issue. Also is t

I have breadboarded a wSHC. Works but takes 3 minutes or so to connect to Blue pill. STM32F303. Wemos D1 etc SWS, android app , stellarium connect immediately. What am I doing wrong? Is there a specif

From: main@onstep.groups.io <main@onstep.groups.io> On Behalf Of Glenn Sammes Sent: Saturday, 15 January 2022 1:01 PM To: main@onstep.groups.io Subject: [onstep] wSHC Hi Guys, I am after some guidance

Hi Guys, I am after some guidance re: wireless SHC. I have bread boarded 2 of them. Intend to make final on VERO (strip board). CPU is ESP32…ESP-WR00m-32 or node MCU-32s Currently using 1.3” displays.

The “B” type cable is a crossover cable. The ends do not have a 1 to 1 correspondence pin wise. The orange and green pairs swap places end to end. In serial terms RX-TX ,TX-RX. Null modem. Not a commo

Thanks Drew, but mine was at 1.06… well out of date. Cheers, Glenn.

Dave, The help was much appreciated. The only reason I was looking for SPI was I mistakenly got an SPI display from Aliexpress when ordered a I2c. (2.4”). Being lazy. Guess I will have to go the hardw

Dave, Cheers mate! Board manager was out of date. Used 2.0.0 because yours is working and mine is not. Figure I am the one with the "problem". Notice there are newer versions however...it now works! H