I've got an LX200 alt/az onstep setup, but a few times now I've had it enter into a state where the android app (which is my main way of fine tuning the position) will only move it in one direction on

Hi, I'm Chris from the UK. I'm looking at onstepping my Eq5 mount and skywatcher 200p and was wondering if there was a recommended option for this?

Hi, My DS3231 burned out (failed to boot with it) so I ordered another one. When I plug new one in it boots, but Time/ Location/Focus resets to zero, same as it is not booted (pwr led glows on DS). As

#define AXIS1_DRIVER_STATUS ON results in an hardware fault message. #define AXIS1_DRIVER_STATUS OFF Motors work fine but obviously no motor status info. For onstep there was TMC_SPI. This I understan

Hello together, long time i useed the 3.16q on MaxPCB1.2 Board Teensy 3.6 with my Formax Mount with the following settings: / AXIS1 RA/AZM // see https://onstep.groups.io/g/main/wiki/6-Configuration#A

I see a lot of these very cheap, from China and one from a reputable source. Is there a recommended place to buy these from?

Hi all , I recently ordered a few miniPCB (version 2) to convert an EQ3-2 mount into a "travel goto mount". It seems like I did not do my homework pretty well , because I can't find any Teensy3.2 for

Hi, My EM10 has been Onstepized for several years now with an Onstep mini version 1 with vertical connectors and wifi. I know that it would be a great challenge maybe impossible to add focusing featur

With an Amazon Fire Tablet, on which I placed SkySafari Pro ($15), we can now get the OnStep mount at Hopewell Observatory to go to any target we want, without any wire connection needed at all. The ‘

Sorry about my silly question, but I'm a Onstep newby. Until now I used a Pulsar I Controller and so the pier side handling in Onstep is a bit confusing for me. I was used to manually set the pier sid

Hi Howard Dutton! I am planning to rebuild an EQ-5 mechanic using OnStep. I decided on MaxSTM3.6, but in connection with the re-design of MaxPCB, would it be important for me to ask whether version 4.

Hello, Small question, having now 2 OnStep, I personalized the 2 wifi to identify them, I would like in the personal SWS the "OnStep" which is written at the top left of all the pages, in which file I

I have run into the SHC's screen to stop responding or show partial information. Is this an indicator of a problem with the OnStep computer not transferring the data to the SHC? The SHC splash screen

I'd like to know if there is any way to reduce STEPS_PER_DEGREE than minimum 3000 usteps? We can't lower it than 3000 in the SWS, I tried it in the firmware and when I fired up the SWS, the value was

Hello: I have a wemos r32 +cnc v3 + wifi wemos d1 mini, and using 2 tmc2130, for now with vref set to 0.8v with screwdriver in pot and multimeter. Putting the board inside the mount, I can´t access th

On the MaxPCB4 the Teensy is not connecting to the WEMOS WIFI processor board. If I set a SERIAL_B baud rate I get a compile error: In file included from H:\OnStepX\src\pinmaps\Models.h:70:0, from H:

As I buy a lot of ESP32s, I get ads for AliExpress of "Next-Teck Products." Mostly RISC 5 development boards with non-ARM instruction set processors that have very little support. So I almost missed t

Hi guys, I've ordered a BME280 sensor recently without paying attention on the interface, in the order it seems to be an SPI sensor. I'm a a bit confused as the sensor has an SDA, SCL and a CSB pin. I

I was looking for information on the ESP32-C3 and came across this announcement from Espressif. ESP32-S2/S3/C3 now supported by Arduino Cloud.

I recently saw some TERRANS Industry branded Goto kits on Aliexpress, which have the name ONSTEP in them. I could not find any reviews of them here. Has anyone tried them? https://www.aliexpress.com/i