Hello, I've searched as well as I could, but is there any way to get the controller to START in Full dual axis + refraction rate compensation mode? I can set the mode in the app, but I cant see any wa

Hello everybody, I would like to recreate the Onstep control based on the MaxESP. Unfortunately I have not yet fully understood what the J14 and J15 headers do. Is anyone able to help me? Thank you, O

Hi all, i try to connect bme280 spi to get ambient weather on the S6 but till now didn't get success. I connected SCK (PA5), MISO (PA6), MOSI (PA7) and CS (PC7) all taken from EXP2 (and pinmap) and 3.

I recently updated my arduino IDE to 1.8.13 and the board tools have changed significantly for the D1 Mini. These are what I used successfully: Board: "LOLIN(WEMOS) D1 R2 & mini" Upload Speed: 115200

Hello everyone, Happy New Year and wishing a lot of health to all of you. I made an attempt to compile/upload the Onstep Master 5.1.f (Firmware Version 4) in my STM32 Bluepill controller but getting a

I cannot change the slew speed during a spiral search. very often I will start a spiral search only to realize I have set the wrong slew speed. I have to stop the search, change the speed and restart

G'day Recently got 2 of these development boards through Aliexpress from RobotDyn to try out - supplier says the boards are compatible with the STM32F103 boards. It is very cheap, slightly faster, has

Thank you everyone in this project to make this happen :) I am finally happy with with my build and therefore ready to share it. Board: Fysetc S6 powered by 19V laptop supply + Wifi + GPS Drivers: 3x

Hello, I've got an STM32 Bluepill running OnStep 3.16o using 2130 drivers. Whats the issue: When using the Android app or the web interface (via WiFi) to move the mount about using the direction butto

I've built a MaxESP3, based on the ESP-WROOM-32 (Node-MCU), 38-pin board. I got it working with the SHC controller (same board), but the motors would only move if I selected a speed of 8X or slower. I

Hi there: I finally pulled out the MKS GEN-L 1.0 board and a couple of TMC 2130 1.1 drivers I've had on the shelf during my (lengthy) 16" build and discover the world has left me behind again! I just

Hi finally my STM32 pcb is working and OnStep is up and running. After long waiting, there was also a good night to test with real starry sky - it worked. There are still a few open questions, but at

Dear Onstep members, I want to present a part of my work snd ask for ideas and possibly feature improvements. Recently I made an observatory class mout from pilloe block bearings, shafts of 50mm diame

Hi All I've recently bought the F303CC and tried to upload, but received a "No debug probe detected" message (see below). My board and 'upload settings', etc as exactly as per Khalid's youtube video.

Hi shortly I converted a EQ5 to OnStep and was impressed about the good results. Thanks to everybody contributing to this! So I moved on and invested in a more stable mount. By chance I bought a used

Hi, The WIKI for the FYSETC states: "In order to use this board, you need to install the STM32Duino board manager. Details available on this page (Getting Started · stm32duino/wiki Wiki · GitHub). You

Last year I made an equatorial mount using Harmonic reducer.Tested recently, The test was conducted recently, the following are the details and test results of the equatorial mount Please see here htt

Some lifehack here guys, especially as a temporarily solution... If you happened to realize, you need a longer mounting plate, the common 2040 aluminum profile works quite well, for the purpose., just

Hi Howard! There is a program to tracking satellites and the ISS (Sazellite Tracker) especially for LX200 telescopes. In "LX200GPS Polar" mode the tracking is absolutely continous. I wanted to take a

Hello every everyone, Does anybody knows a simple way to know what version Onstep code (freshly downloaded) was prior uploading on the Onstep Hardware controllers ? Thanks +Plamen