Is anyone using PEC with INDI driver and Kstars? I tried recently and it did not work as expected: I recorded one worm rotation and after PEC started playing, I did not see any change in terms of peri

I still have two MaxPCB2 boards lying around and would set up an OnStep for another mount. Since I need around 2A current for the motors, I am just wondering if there is a possibility to operate the T

Good day folks I just received my S6 from aillexpree and apon an examinations in the board I found something that doesn't look right I enclosed a picture with it looks like a bridge at the pa2 pad in

Hello All, I have posted an explanation few moths ago of my problems "STM32 BluePill bunches of weirdness" ( unexpected high angular velocity of DEC motor followed of stalling while doing Goto) : http

Hello everyone, I am trying to see whether the SHC I have built works. It flashed correctly. So far so good. ST4_HAND_CONTROL is set to ON and ST4_INTERFACE is set to ON_PULLUP in Config.h. When I con

I've been wondering why a resistor is disconnected (10K pullup) and a flat pack or discrete pullup resistors are needed with the CNC V3 shield... Checking the schematics, I see that the SHC (Smart Han

Starting to get my head around the preparations for flashing the FYSETC S6 but one of the issues that delayed me was not being able to find the stm32CubeProg.bat file in the Arduino15 folder that requ

Wemos D1 R32 with CNC V3... // ST4 INTERFACE ------------------------------------------------------ see https://onstep.groups.io/g/main/wiki/6-Configuration#ST4 // *** It is up to you to verify the in

I was finally able to convert my CGEM to use Onstep with Fysetc S6 board and belt drives. I see dramatic improvement in the auto guiding. However I think I have to adjust backlash settings a bit more

Hi, I have start working on motorizing my truss dob using the onstep system. I'm thinking to use the cable solution for the altitude bearing but my bearings are foldable. Is it going to work on this w

The Power Led on the board is on, but the PC13 only blinks, did the test with the i2cscanner and is detecting the correct address of eeprom and RTC, did the blink test works as it is suppose, checked

Running the bluepill board with STM32F303 chip here, BME280 as the weather sensor. First issue I have, the Humidity is Always 100%, tested within several days, always 100%, the other data seems to cha

I'm currently playing around with the mount of a beginner telescope before moving to something more advanced and I'm stuck with a question. I rebuilt the mount for this scope from a cheesy AZ mount to

As per title the small monetary donation link on the main wiki page is broken. Error 404

I am having problems getting the onstep ASCOM drivers to work on an XP laptop. I'm running ASCOM build 6.0.6056.1963 which has worked well with an heq5 and Vixen skysensor 2000 in the past. I've tried

I am busy converting a LXD55 mount. The aim is to fit everything (except the Focuser Driver) into the existing case around the RA motor. I will be using a RobotDyn STM32F303 board as controller and be

Hi, guys I just finished up my MKS gen 2 but my gotos are very slow here is my config file I tried everything to speed it up but with no luck. it has 5610 drivers I used pulse and Square took off the

i wanted to thank everyone for such a great project and supper support. Special thanks to Howard and Khalid for there expertise. Enclosed is a video of the scope moving with onstep. It's not done yet

I gather FYSETC advocates the use of the external SD card supplied with the S6 board for loading firmware. It plugs into EXP 1 on the board. Can it be used for loading Onstep to this board? Gerry Byrn

Hi I'm new here so forgive me if this has been discussed before. I trying to use a WeAct F401 blackpill with the STM32 Bluepill PCB. Before mounting the components on the PCB which will doubtless invo