Date
1 - 5 of 5
Compile error
|
Hi there: C:\Users\gordt\Dropbox\ File dataFile = FS.open(www.uri().c_str(), FILE_READ); ^~~~ C:\Users\gordt\Dropbox\ File dataFile = FS.open(www.uri().c_str(), FILE_READ); ^~~~ Wire C:\Users\gordt\Dropbox\ if (dataFile) { ^~~~~~~~ C:\Users\gordt\Dropbox\ if (dataFile) { ^~~~~~~~ mutable exit status 1 Error compiling for board Arduino Mega or Mega 2560. Here's my config.h, I pretty much left everything turned off for the first load of the software: // --------------------------------------------------------------------------------------------------------------------------------- // Configuration for the Observatory Control System (OCS) /* * For more information on setting the OCS up see http://www.stellarjourney.com/index.php?r=site/observatory_control * and join the OCS Groups.io at https://onstep.groups.io/g/onstep-ocs */ // ****** _RELAY and _SENSE numbers are mapped to pins in a platform specific pinmap, see: /src/pinmaps ****** // ****** Additional settings are present in /src/Config.defaults.h ****** // --------------------------------------------------------------------------------------------------------------------------------- // ADJUST THE FOLLOWING TO CONFIGURE YOUR CONTROLLER FEATURES ---------------------------------------------------------------------- // <-Req'd = always must set, <-Often = usually must set, Option = optional, Adjust = adjust as req'd, Infreq = infrequently changed // PINMAP -------------------------------------------------------------------------------------------------------------------------- #define PINMAP LEGACY // OFF, Choose from: LEGACY, OCS1, OCS2, OCS3, OCS4, OCS4E. <-Req'd // Other boards/more info. in /src/Constants.h // WATCHDOG SETTINGS --------------------------------------------------------------------------------------------------------------- #define WATCHDOG OFF // OFF, ON resets OCS after 8 sec. if it hangs for (nearly) any reason. Option // NETWORK SETTINGS ---------------------------------------------------------------------------------------------------------------- #define ASCOM_ALPACA_SERVER OFF // OFF, ON enables ASCOM Alpaca server on port 10000, requires W5500 Ethernet. Option // Note: this disables the IP command servers on ports 9998, 9999 and // works best w/my Ethernet library from: https://github.com/hjd1964/Ethernet #define CONNECT_CHECK_HOURS OFF // OFF, n. Where n=1 to 48 (hours.) Connection check time. Option #define CONNECT_IP_ADDR {100,24,172,113} // Default is arduino.cc. Needs ETHERNET_RESET_PIN and/or WATCHDOG to reset. #define CONNECT_FAIL_WATCHDOG OFF // OFF, ON to stop all processing and trigger the watchdog reset. Option // TIME SETTINGS ------------------------------------------------------------------------------------------------------------------- #define TIME_LOCATION_SOURCE NTP // NTP, Network Time Protocol w/IP address settings in Extended.config.h or Adjust // DS3234 on default SPI interface and default CS pin or DS3231 on I2C. #define TIME_IP_ADDR {129,6,15,28} // ...6,15,28}, time-a-g.nist.gov at 129,6,15,28 or 129,6,15,29, 129,6,15,30, etc. Option #define TIME_ZONE -5 // -5, Time Zone (US Eastern Standard Time in this case.) <-Req'd #define TIME_DISPLAY STD // STD, Display Standard Time, UT1 to display Universal Time. Adjust // STATUS PANEL FEATURES ----------------------------------------------------------------------------------------------------------- #define STAT OFF // OFF, ON to enable the OCS website status panel display. Option #define STAT_UNITS METRIC // METRIC, For metric units, or IMPERIAL for imperial units. Adjust #define STAT_MAINS_SENSE OFF // OFF, n. Where n=1..8 (Sense#) mains power good, OFF (power failure) is UNSAFE Option #define STAT_MAINS_CURRENT_ANALOG OFF // OFF, n. Where n=1..16 (Analog#) measure/display current mains. Option #define STAT_MAINS_AUX_CURRENT_ANALOG OFF // OFF, n. Where n=1..16 (Analog#) measure/display current mains (aux.) Option // Converts the analog measure (range 0 to 1.0) to Amps #define STAT_MAINS_ANALOG_TO_CURRENT(x) (x*NAN) #define STAT_DC_VOLTAGE_ANALOG OFF // OFF, n. Where n=1..16 (Analog#) measure/display 12VDC power supply voltage. Option #define STAT_DC_CURRENT_ANALOG OFF // OFF, n. Where n=1..16 (Analog#) measure/display 12VDC power supply current. Option #define STAT_BATTERY_VOLTAGE_ANALOG OFF // OFF, n. Where n=1..16 (Analog#) measure/display 12V roof battery voltage. Option #define STAT_BATTERY_CURRENT_ANALOG OFF // OFF, n. Where n=1..16 (Analog#) measure/display 12V roof battery current. Option // Converts the analog measure (range 0 to 1.0) to Volts #define STAT_DC_ANALOG_TO_VOLTAGE(x) (x*NAN) // Converts the analog measure (range 0 to 1.0) to Amps #define STAT_DC_ANALOG_TO_CURRENT(x) (x*NAN) #define STAT_PROCESSOR_RAM OFF // OFF, ON for display of Processor free RAM resources. Mega2560 only. Option // POWER PANEL --------------------------------------------------------------------------------------------------------------------- #define POWER OFF // OFF, ON to enable the OCS website power panel display. Option #define POWER_DEVICE1_RELAY OFF // OFF, n. Where n=1..18 (Relay#) with _NAME below. Option #define POWER_DEVICE1_MEMORY OFF // OFF, ON to enable memory (across power cycles) for this relay state. Option #define POWER_DEVICE1_NAME "" #define POWER_DEVICE2_RELAY OFF // OFF, n. Where n=1..18 (Relay#) with _NAME below. Option #define POWER_DEVICE2_MEMORY OFF // OFF, ON to enable memory (across power cycles) for this relay state. Option #define POWER_DEVICE2_NAME "" #define POWER_DEVICE3_RELAY OFF // OFF, n. Where n=1..18 (Relay#) with _NAME below. Option #define POWER_DEVICE3_MEMORY OFF // OFF, ON to enable memory (across power cycles) for this relay state. Option #define POWER_DEVICE3_NAME "" #define POWER_DEVICE4_RELAY OFF // OFF, n. Where n=1..18 (Relay#) with _NAME below. Option #define POWER_DEVICE4_MEMORY OFF // OFF, ON to enable memory (across power cycles) for this relay state. Option #define POWER_DEVICE4_NAME "" #define POWER_DEVICE5_RELAY OFF // OFF, n. Where n=1..18 (Relay#) with _NAME below. Option #define POWER_DEVICE5_MEMORY OFF // OFF, ON to enable memory (across power cycles) for this relay state. Option #define POWER_DEVICE5_NAME "" #define POWER_DEVICE6_RELAY OFF // OFF, n. Where n=1..18 (Relay#) with _NAME below Option #define POWER_DEVICE6_MEMORY OFF // OFF, ON to enable memory (across power cycles) for this relay state. Option #define POWER_DEVICE6_NAME "" // LIGHTING PANEL ------------------------------------------------------------------------------------------------------------------ #define LIGHT OFF // OFF, ON to enable the OCS website lighting panel display. Option #define LIGHT_WRW_RELAY OFF // OFF, n. Where n=1..18 (Relay#) for Warm room white lights. Option #define LIGHT_WRR_RELAY OFF // OFF, n. Where n=1..18 (Relay#) for Warm room red lights. Option #define LIGHT_ORW_RELAY OFF // OFF, n. Where n=1..18 (Relay#) for Observing room white lights. Option #define LIGHT_ORR_RELAY OFF // OFF, n. Where n=1..18 (Relay#) for Observing room red lights. Option #define LIGHT_OUTSIDE_RELAY OFF // OFF, n. Where n=1..18 (Relay#) for Outside flood. Option #define LIGHT_SW_SENSE OFF // OFF, n. Where n=1..8 (Sense#) for switch to turn WRW lights on/off. Option // WEATHER PANEL ------------------------------------------------------------------------------------------------------------------- // Weather and Sky Conditions web page charts use "Chart.js" http://www.chartjs.org/. Specifically, version 2.5 of "Chart.min.js" // renamed to "Chart.js" and placed in the Micro SD card root directory (Fat32 formatted) and inserted into the W5100 Ethernet // adapter. Downloaded from here https://github.com/chartjs/Chart.js/releases/tag/v2.5.0 (page bottom for download links.) #define WEATHER OFF // OFF, ON to enable the OCS website weather panel display. Option #define WEATHER_CHARTS OFF // OFF, ON for logging and display of weather data graphic charts. Option #define WEATHER_TEMPERATURE OFF // OFF, ON for measuring outside temperature. Option #define WEATHER_PRESSURE OFF // OFF, ON for measuring barometric pressure. Option #define WEATHER_NOMINAL_PRESSURE 1010 // 1010, n. Where n=500..1050 (in mb) site nominal pressure for Chart. Adjust #define WEATHER_ALTITUDE 100 // 100, n. Where n=-86..5000 (meters) site altitude. Adjust #define WEATHER_HUMIDITY OFF // OFF, ON for measuring outside humidity. Option #define WEATHER_WIND_SPD OFF // OFF, ON for measuring wind speed. Option #define WEATHER_WIND_SPD_THRESHOLD 20 // 20, n. Where n=0..100 (in kph) wind speed above this is considered UNSAFE. Adjust #define WEATHER_RAIN OFF // OFF, ON to enable rain sensor, a "wet" condition is considered to be UNSAFE. Option #define WEATHER_CLOUD_CVR OFF // OFF, ON to enable the cloud sensor, above WEATHER_SAFE_THRESHOLD is UNSAFE. Option #define WEATHER_SAFE_THRESHOLD -14 // -14, n. Where n=-25..0 (in Deg. C) Adjust #define WEATHER_VCLR_THRESHOLD -19 // -19, n. Where n=-25..0 (in Deg. C) Adjust #define WEATHER_CLER_THRESHOLD -17 // -17, n. Where n=-25..0 (in Deg. C) Adjust #define WEATHER_HAZE_THRESHOLD -14 // -14, n. Where n=-25..0 (in Deg. C) Adjust #define WEATHER_OVRC_THRESHOLD -11 // -11, n. Where n=-25..0 (in Deg. C) Adjust #define WEATHER_CLDY_THRESHOLD -8 // -8, n. Where n=-25..0 (in Deg. C) Adjust #define WEATHER_VCLD_THRESHOLD -5 // -5, n. Where n=-25..0 (in Deg. C) Adjust #define WEATHER_SKY_QUAL OFF // OFF, ON for measuring sky quality (darkness in magnitudes per sq arc-sec.) Option // WEATHER SENSORS ---------------------- #define WEATHER_SENSOR_TPH_BME280 OFF // OFF, 0x76 or 0x77 (I2C Address) to enable. Temperature, pressure, humidity. Option #define WEATHER_SENSOR_TP_BMP280 OFF // OFF, 0x76 or 0x77 (I2C Address) to enable. Temperature, pressure. Option #define WEATHER_SENSOR_TP_BMP085 OFF // OFF, 0x77 (I2C Address) to enable. Temperature, pressure. For BMP180 also. Option #define WEATHER_SENSOR_TH_DHT OFF // OFF, n. Where n=1..8 (Sense#) to enable. Temperature, humidity. Option // DHT device type DHT11, or DHT21, DHT22 #define WEATHER_SENSOR_TH_DHT_TYPE DHT11 #define WEATHER_SENSOR_TH_SI7021 OFF // OFF, 0x40 (I2C Address) to enable. Temperature, humidity. Option #define WEATHER_SENSOR_T_ANALOG OFF // OFF, n. Where n=1..16 (Analog#) to enable. Option // Conversion factor, analog range 0 to 1.0 (x) to Deg. C; example TMP36 device 0.1V (-40°C) to 2.0V (150°C) w/3.3V MCU #define WEATHER_SENSOR_T_ANALOG2DEGC(x) (((x*3.3)-0.1)*100.0-40.0) #define WEATHER_SENSOR_WIND_CUP OFF // OFF, n. Where n=1..8 (Sense#) to enable. Wind speed, cup anemometer. Option // Conversion factor, pulses per minute (x) to wind speed in KPH #define WEATHER_SENSOR_WIND_CUP2KPH(x) (x*0.087) #define WEATHER_SENSOR_WIND_REV_P OFF // OFF, n. Where n=1..16 (Analog#) to enable. Wind speed. Option #define WEATHER_SENSOR_RAIN_GENERIC OFF // OFF, n. Where n=1..16 (Analog#) to enable. Option #define WEATHER_SENSOR_RAIN_LOW 0.25 // OFF, n. Where n=0.0 to 1.0 for lower range below which is dry. Option #define WEATHER_SENSOR_RAIN_HIGH 0.75 // OFF, n. Where n=0.0 to 1.0 for lower range below which is wet. Option #define WEATHER_SENSOR_CLOUD_MLX90614 OFF // OFF, 0x5A (I2C Address) to enable. Gets IR sky IR temp. for cloud detection. Adjust #define WEATHER_SENSOR_SKYQ_TSL2591 OFF // OFF, 0x28 (I2C Address) to enable. Sky brightness for sky quality estimate. Option // THERMOSTAT PANEL ---------------------------------------------------------------------------------------------------------------- #define THERMOSTAT OFF // OFF, ON to enable the OCS website thermostat panel display. Option #define HEAT_RELAY OFF // OFF, n. Where n=1..18 (Relay#) for indoor heat. Option #define COOL_RELAY OFF // OFF, n. Where n=1..18 (Relay#) for cooling/venting. Option #define THERMOSTAT_HUMIDITY OFF // OFF, ON displays indoor humidity. Option // THERMOSTAT SENSORS ------------------- #define THERMOSTAT_SENSOR_TPH_BME280 OFF // OFF, 0x76 or 0x77 (I2C Address) to enable. Temperature, pressure, humidity. Option #define THERMOSTAT_SENSOR_TP_BMP280 OFF // OFF, 0x76 or 0x77 (I2C Address) to enable. Temperature, pressure. Option #define THERMOSTAT_SENSOR_TP_BMP085 OFF // OFF, 0x77 (I2C Address) to enable. Temperature, pressure. For BMP180 also. Option #define THERMOSTAT_SENSOR_TH_DHT OFF // OFF, n. Where n=1..8 (Sense#) to enable. Temperature, humidity. Option // DHT device type DHT11, or DHT21, DHT22 #define THERMOSTAT_SENSOR_TH_DHT_TYPE DHT11 #define THERMOSTAT_SENSOR_TH_SI7021 OFF // OFF, 0x40 (I2C Address) to enable. Temperature, humidity. Option #define THERMOSTAT_SENSOR_T_ANALOG OFF // OFF, n. Where n=1..16 (Analog#) to enable. Option // Conversion factor, analog (x ranges from 0 to 1.0) to Deg. C; example TMP36 0.1V (-40°C) to 2.0V (150°C) w/3.3V MCU #define THERMOSTAT_SENSOR_T_ANALOG2DEGC(x) (((x*3.3)-0.1)*100.0-40.0) // ROOF/SHUTTER CONTROL PANEL ------------------------------------------------------------------------------------------------------ #define ROOF OFF // OFF, ON to enable the OCS website roof/dome shutter panel display. Option #define ROOF_USER_SAFETY_OVERRIDE OFF // OFF, ON displays safety override button. Option #define ROOF_AUTOCLOSE_DAWN OFF // OFF, ON displays option to automatically close roof at dawn. Option #define ROOF_AUTOCLOSE_DAWN_DEFAULT OFF // OFF, ON enables AUTOCLOSE_DAWN option at startup, disabled otherwise. Option #define ROOF_AUTOCLOSE_SAFETY OFF // OFF, ON closes the roof automatically if an UNSAFE condition is detected. Option #define ROOF_MOTOR_OPEN_RELAY OFF // OFF, n. Where n=1..18 (Relay#) engages this relay to open roof. Option #define ROOF_MOTOR_CLOSE_RELAY OFF // OFF, n. Where n=1..18 (Relay#) engages this relay to close roof. Option #define ROOF_MOTOR_RELAY_MOMENTARY OFF // OFF, ON engage above momentarily (~1.5s) to start an automatic open or close. Option #define ROOF_MOTOR_STOP_RELAY OFF // OFF, n. Where n=1..18 (Relay#) momentarily engages this relay to stop roof. Option #define ROOF_POWER_RELAY OFF // OFF, n. Where n=1..18 (Relay#) This controls roof motor power. For DC motors Option // SSR/MOSFET PWM controls speed. For garage door openers etc SW on/off only. #define ROOF_POWER_PWM_FREQUENCY OFF // OFF, n. Where n=1..100 (Hz) PWM frequency for roof motor DC control. Option #define ROOF_POWER_PWM_POWER OFF // OFF, n. Where n=10..100 (%) PWM power level for roof motor DC control. Option #define ROOF_POWER_PWM_SOFTSTART OFF // OFF, ON For PWM soft start, start 0% adds 5%/sec until ROOF_POWER_PWM_POWER. Option #define ROOF_INTERLOCK_SENSE OFF // OFF, n. Where n=1..8 (Sense#) Roof safety interlock, close allowed when ON. Option #define ROOF_LIMIT_CLOSED_SENSE OFF // OFF, n. Where n=1..8 (Sense#) Roof closed switch (CLOSED when ON.) Option #define ROOF_LIMIT_OPENED_SENSE OFF // OFF, n. Where n=1..8 (Sense#) Roof open switch (OPEN when ON.) Option #define ROOF_TIME_AVG 300 // 300, n. Where n=30..1200 (seconds) Average time to open or close roof. Adjust #define ROOF_TIME_TOL 30 // 30, n. Where n=0..120 (seconds) Additional time before stop & error thrown. Adjust // DOME CONTROL PANEL -------------------------------------------------------------------------------------------------------------- #define DOME OFF // OFF, ON to enable the OCS website dome panel display. Option #define DOME_SHUTTER_LOCK OFF // OFF, ON to disable dome motion unless shutter is open. Option // Usually this will be a GENERIC stepper driver or a servo SERVO_PD (PWM/Direction) or SERVO_II (PWM/PWM) #define AXIS1_DRIVER_MODEL OFF // OFF, Enter driver model (above) to activate the dome Azimuth axis. Option #define AXIS1_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. Option #define AXIS1_DRIVER_STATUS OFF // OFF, ON, HIGH, or LOW. For driver status info/fault detection. Option // for SERVO_II and SERVO_PE driver models, PID and encoder settings: #define AXIS1_SERVO_ENCODER ENC_AB // ..._AB, Encoder type, ENC_AB, ENC_CW_CCW, ENC_PULSE_DIR, ENC_PULSE_ONLY. Adjust #define AXIS1_SERVO_P 2.0 // 2.0, Proportional; scale of immediate response to position error. Adjust #define AXIS1_SERVO_I 5.0 // 5.0, Integral; rate of increasing response to position error over time. Adjust #define AXIS1_SERVO_D 1.0 // 1.0, Derivative; overshoot supression. Adjust #define AXIS1_SLEW_RATE_DESIRED 1.0 // 1.0, n, (degrees/second) Maximum speed depends on processor. Adjust #define AXIS1_STEPS_PER_DEGREE 60.0 // 60.0, n. Number of steps per degree for dome. Adjust #define AXIS1_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. Option #define AXIS1_POWER_DOWN OFF // OFF, ON Powers off 30sec after movement stops or 10min after last<=1x guide. Option #define AXIS1_LIMIT_MIN -180 // -180, n. Where n= 0..-360 (degrees.) Minimum Azimuth. Adjust #define AXIS1_LIMIT_MAX 180 // 180, n. Where n= 0.. 360 (degrees.) Maximum Azimuth. Adjust #define AXIS1_SENSE_HOME OFF // OFF, HIGH or LOW enables & state clockwise home position, as seen from front. Option #define AXIS1_SENSE_LIMIT_MIN OFF // OFF, HIGH or LOW state on limit sense switch stops movement. Option #define AXIS1_SENSE_LIMIT_MAX OFF // OFF, HIGH or LOW state on limit sense switch stops movement. Option // Digital, optionally add: |HYST(n) Where n=0..1023 stability time in ms. // Analog capable sense inputs also allow adding: // |THLD(n) Where n=1..1023 (ADU) for Analog threshold. // |HYST(n) Where n=0..1023 (ADU) for +/- Hystersis range. #define AXIS1_WRAP OFF // OFF, ON Allows unlimited Azm range and ignores min/max limits. Option #define AXIS2_DRIVER_MODEL OFF // OFF, Enter driver model to activate the (optional) dome Altitude axis. Option #define AXIS2_DRIVER_MICROSTEPS OFF // OFF, n. Microstep mode when tracking. Option #define AXIS2_DRIVER_STATUS OFF // OFF, ON, HIGH, or LOW. For driver status info/fault detection. Option // for SERVO_II and SERVO_PE driver models, PID and encoder settings: #define AXIS2_SERVO_ENCODER ENC_AB // ..._AB, Encoder type, ENC_AB, ENC_CW_CCW, ENC_PULSE_DIR, ENC_PULSE_ONLY. Adjust #define AXIS2_SERVO_P 2.0 // 2.0, Proportional; scale of immediate response to position error. Adjust #define AXIS2_SERVO_I 5.0 // 5.0, Integral; rate of increasing response to position error over time. Adjust #define AXIS2_SERVO_D 1.0 // 1.0, Derivative; overshoot supression. Adjust #define AXIS2_SLEW_RATE_DESIRED 1.0 // 1.0, n, (degrees/second) Maximum speed depends on processor. Adjust #define AXIS2_STEPS_PER_DEGREE 60.0 // 60.0, n. Number of steps per degree for dome. Adjust #define AXIS2_REVERSE OFF // OFF, ON Reverses movement direction, or reverse wiring instead to correct. Option #define AXIS2_POWER_DOWN OFF // OFF, ON Powers off 30sec after movement stops or 10min after last<=1x guide. Option #define AXIS2_LIMIT_MIN 0 // 0, n. Where n= 0..90 (degrees.) Minimum Altitude. Adjust #define AXIS2_LIMIT_MAX 90 // 90, n. Where n= 0..90 (degrees.) Maximum Altitude. Adjust #define AXIS2_SENSE_HOME OFF // OFF, HIGH or LOW enables & state clockwise home position, as seen from front. Option #define AXIS2_SENSE_LIMIT_MIN OFF // OFF, HIGH or LOW state on limit sense switch stops movement. Option #define AXIS2_SENSE_LIMIT_MAX OFF // OFF, HIGH or LOW state on limit sense switch stops movement. Option #define FileVersionConfig 2 #include "Extended.config.h" |
|
|
|
Howard Dutton
On Wed, Jul 27, 2022 at 11:56 AM, Gord Tulloch wrote:
Just starting to put together my system - I have a mega2560 and ethernet shield ready to go but am hung up on compiling the sketch in the Arduino IDE, with the following error. Any assistance would be appreciated - I've programmed a lot in C but not on Arduino, so although it looks like a library isn't being loaded none of the libraries I'd tried loading seem to work.There was a little issue with those basic settings that was tripping it up. Download again, should be good now. |
|
|
|
Howard Dutton
On Wed, Jul 27, 2022 at 11:56 AM, Gord Tulloch wrote:
I've programmed a lot in C but not on Arduino, so although it looks like a library isn't being loaded none of the libraries I'd tried loading seem to work.The condition for the SD library being brought in was the weather panel being enabled; that was due to how the OCS worked long ago. It's now a Config.defaults.h (default) setting #define SD_CARD ON that brings in that library and functionality. |
|
|
|
Howard Dutton
Please have a look at the Wiki too if you haven't done so already:
https://onstep.groups.io/g/onstep-ocs/wiki |
|
|
|
Yup have gone over the wiki pretty carefully, thanks for all that work! I actually found that the SD library brought in the File type but adding it didn't resolve the problem - some kind of conflict somewhere! The sketch now compiles and loads so good to go thanks! |
|
|